Be careful ! in France you are not allowed to transmit in realtime video from an aircraft !

You need:

  • Aurel H2-TV Channel Audio-Video Modulator
    Mod. MAV-VHF224
    225 Fr

    Description :
    Low cost CATV circuit for high quality audio-video signals, operating in the VHF Band. Input signals can be fed from videocameras, tuners, video tape players, etc, directly using the lines of the standardized output connectors (i.e. SCART), while output R.F. can be received with any standard not modified TV receiver. The Modulator is very stable in frequency and features high harmonic rejection.
Characteristics Min Typ Max Unit
VS Supply Voltage 4.75 5 5.25 Vdc
IS Supply Current   90   mA
PO RF Output power   1   mW
IM 3rd Order Intermodulation     60 dBm
FC Carrier Frequency 223.75 224.5 225.25 MHz
IM Video Input Modulation   1.2   Vpp
FSC Sub-Carrier Frequency   5.5   MHz
MA Audio FM Modulation   1   Vpp
II Input Impedance   100   KW
TPE Pre-enphasis   50   S
TOP Operating temperature range -20   +80 °C
Pin-Out
1 Ground
2 Audio Input
3 Ground
4 Video Input
5 Ground
6 +5V
7 Ground
8 RF Output
  • Aurel H2 Channel CATV Amplifier
    Mod. M.C.A. 224
    130 Fr

    Description :
    Linear CATV circuit for high quality audio-video signal amplification, operating on the VHF H2 Channel. RF input signal can be derived from a Audio Video Modulator (best operation is with our mod. MAV-VHF 224). Output can be received with any standard not modified TV receiver.
Characteristics Min Typ Max Unit
VS Supply Voltage 11.4 12 12.6 Vdc
IS Supply Current   100   mA
FW Working Frequency   224   MHz
PO RF Output power (2 mW IN)   +19   dBm
DI Intermodulation distorsion   50 60 dB
TOP Operating temperature range -20   +80 °C
Pin-Out
1 +12v
2 Enable
3 Ground
6 RF Input
7 Ground
10 Ground
13 Ground
15 RF Output
  • Mini color video cam 890 Fr
Characteristics
Video system PAL
Effective pixel 628*582
Synchro internal
Resolution (TV lines) 380
S/N Ration > 42 dB
Mill Illumination 3 lux at F1.2
Electronic shutter 1/50 - 1/150 000
Video output 1V , 75 Ohms
Lens 3.6 mm - 5 mm (F 2 -> 4.5)
Lens Angle 92° -> 65°
Power current 50 mA
Power Source DC12V
Pin-Out
Red +12v
Yellow signal
Black Ground
  • a good and safety box (in case of crash) 18 Fr
  • Accus (2 * 9V), a free rx channel. 296 Fr
  • 2 voltage regulator : 7812 (12V) and 7805 (5V) + 2 * 100 nF 27 Fr
  • A small TV (LCD) ex 11cm TFT 1000 Fr

Conclusions :

The result is very bad with no specific antenna, maybe I should replace my 32 cm wire with something better. Distance are bad too and some polarized effect appear when you turned the device : Really BAD !

Â

comments powered by Disqus

You might like also

2.4GHz RC transmitter are the future
I am the proud owner of a Futaba Force field 9 (aka FF9) working in PCM mode 41.080Mhz. I came across some links saying that before 2011, I will be forced to throw it away or try to convert it in 35MHz (costs of conversion would out pass a new transmitter). In fact 41MHZ has been assigned to military in France, and is already forbidden in Switzerland... While Googling about more info on that subject, I found a lot of …
4416 Days ago
FUTABA 14Mz windows ce
Double the resolution of PCM 1024, The HVGA screen features crystal-clear 640x240 pixel resolution, 2 internal processors for maximum efficiency and reliability. Windows CE (quite dangerous :-) ). www.14mz.com FlyRC My review: Too expensive: for $2000 you can have a Futaba 9z (top of the line) + a very good ladtop Nobody will be looking at the colour screen while flying: too dangerous for the aircraft Telemetry feature are missing (altitude or better main rotor rpm for helicopter) …
5182 Days ago
Read rc helicopter main rotor RPM realtime
THIS IS STILL A PROTOTYPE; NOT TESTED OR WORKING!!!!!! TECHNICAL HELP OR REVIEW APRECIATED (I&39;M A POOR SOFTWARE ENGINEER...) Â Status: 11.01.2003 Tx and Rx are working with the 2 voltage regulator. the switching circuit on the rx side is not commutting as expected. Help needed! 26.01.2003 measure the current to correctly determine the values of R for the bipolar transistor switch I NEED YOUR HELP! I f you can resolve this, feel free to contact me, all ideas are …
5277 Days ago
Video Camera: using 2.4 GHz transmitter.
Be careful ! in France you are not allowed to transmit in realtime video from an aircraft !You need : Velleman 2.4 GHz wireless surveillance system 1700 Fr include a high res color video camera, ability to have 4 different TX, built in microphone, and 300 feet range. Accus (2 * 9V) 296 Fr1 voltage regulator : 7812 (12V) + micro switch 7 Fr Rx rx_front.jpg rx_rear.jpg Tx I remove some part to have less parts.... tx_front.jpg tx_right.jpg Add a …
5277 Days ago
For Simulator
How to build your own realistic controler (for Realflight®, or any other simulator that use a regular joystick). All you need is to kill an old radio, extract PCB, and solder some cable. All credits to : http://www.iquebec.com/st-prime/modif_rc.html where the following picture was extracted. radio_ordi.jpg Connect CSM 10 to a futaba FF9 : You must own the dongle, we only want to bypass the use of the jack connector and use a DIN..or connect to the proprietary connector.. There is …
5277 Days ago
For Transmitter
FUTABA Training cord cost 160 FF build 28 FF AM version FM version CAMPAC memory extension and backup to PC with excel table cost 75€ to build only 6€ (EEPROM 2.5€) Plan + software (http://members.telocity.com/fritzthecat/campac.html ) Work only for the FF8, not for the WC or FF9 ! …
5277 Days ago
For gyroscopes
CSM 540 Cable for PC + Software cost 30€ to build only 5€ Softwar Here Documentation (winword manual) …
5277 Days ago