Parts needed

The WaterCUBE GT3 guarantees shiver performances and temperatures of exercise under control also with emiting CPU more than 100 Watts (power calculated with overclocked and under stress CPU).
The kit includes the Waterblock, the clip of fixing on socket A/370 and 2,5 mt of Crystal Extraflex pipes.

Size: 50x50x47 mm.
Weight: 260 gr.
Material: Copper,Aluminum
Pipes: internal diameter 8 mm. – outside diameter 12 mm – thickness 2 mm

Next-Cool guarantees all of his products 24 months from defects of manufacture.

innovakool 3.0 mounted on PC2

The AGB-O-Matic is used for filling and de-aerating a water cooling system. The use of this device is very simple: You just need to plug it onto the EHEIM pump. Then, the pump can suck in the fresh water directly and absolutely free of blow holes.
Despite of the slim design of 50x56x120 mm, the AGB-O-Matic provides a huge filling volume. The tank is leakproofed which makes it possible to transport the device easily. After installing the AGB-O-Matic, the water cooling system is filled though the aparture at the top (see picture).

Details:
The AGB-O-Matic is optimized for the Eheim pumps 1046 and 1048. It consists of glass fibre reinforced plastics.
As standard, the runback flow is equipped with one 8×1 screw connection. The 1/4 inch screw thread makes it possible to use other connectors and therefore to combine the AGB-O-Matic with tubes that have other diameters.

Technical facts:
Weight: 110 g
Material: Glass fibre reinforced plastics
Dimensions (without the pump): 50x56x120 mm
Fits with Eheim 1046 and 1048
Equipped with one 8×1 screw connection

• Very powerful design with large surface (the copper pipe is more than 6 m long)
• the cooling liquid flows parallel through the pipes at the same time which helps to avoid streaming loss
• Turbo fins for optimal heat dissipation
• Antechamber for the air which provides consistent pressure build-up
• Optimized for slow rotating fans with a diameter of 120 mm
• fan installation using included screw threads
• screw threads at both sides of the cooling unit for installation in or at the case
• high quality material
• G ¼ inch screw-in sockets for installation with all connecting systems
• robust powder coating

Material: Pipes: copper (diameter 8 mm), Fins: aluminium, Sides: stainless steal
Dimensions outside: 285 x 137 x 58 mm
Installation: 8x M4 screw threads on top (for two fans with a diameter of 120 mm), 4x M4 screw threads at both sides (for the installation in or at the case)
Compressive strength: until 30 bar
Surface: black, powder coating, stainless steal, polished
Connection: 2x screw threads G ¼ inch (angel of 90°)
Included in delivery: HT-Flat, instructions for installation, 8x M4 screws, hex-wrench, 2-year-guarantee for pressure tightness and workmanship

Flow-O-Matic electronic flow monitoring is used for active electronic flow monitoring in the water circulation of your watercooling.It is simply put into the cycle and then emits a signal, as long as a flow is present.It is simply attached to the Main board and the emited signal can be analyzed by the BIOS or suitable software (e.g. MBM). It contains also 2 bue leds.

1048 Centrifugal pump
Pump performance 600 l/h
Hoisting hight 1,50 mWs
Power consumption 10 W
Tube connection suction-sided (ingoing) Ã?13mm
Tube connection pressure-sided (outgoing) Ã?13mm
Measurements mm 145 x 75 x 118 mm

The pump is hardly audible and can be used in and outside of the water. It has a 220 volt connection.

Dimensions: 120x120x25mm
Voltage: 12 Volt
Air flow: 2,30³/min
revolutions: 2000 r/min
Volume: <36dB

This fan has a very good cooling performance and can still be run at 7 V without losing much performance. Furthermore, it passes the number of revolutions on to the Mainboard.

In the extent of supply 4 screws are included for attachment to the casing or the radiator.